9U Wood End Powered
9U Wood End Powered
9U Wood End Powered

 
9U Studio case
84HP
Wooden Panels
Power 1.5A +/-12V & 0.5A 5V
Made in France
 
In stock. Shipping in 24 H.Contact

365,00  Add to cart
Bend KIT
Bend KIT

 

  • Type/ Controller
  • Width/ 4HP
  • Power/ +?mA/-?mA
  • Depth/ ?mm

 
The DIY Bend kit is a fun way to bring touch sensitivity into your modular instrument. This simple build will have you touch controlling filter cutoff, pitch, lfo rate or any other CV input you can imagine within 30 minutes. The potentiometer attenuates the CV output, the hold control holds on the last touched position of the strip. Without the hold switch off, CV signal is only sent when touching the sensor.
This is a great first project. Swat up on some soldering instructions via youtube and take your time, reading the instructions twice before beginning.
 
Download the Bend KIT manual HERE
 
In stock. Shipping in 24 H.Contact

59,00  Add to cart
Bus Board
Bus Board

 
Simple bus board with 15 headers and LED indicators to check your +12 and -12 rails are working. No voltage is exposed on the underside, so these boards can be fixed to any case, metal included. Two bus boards can be wired together easily using the solder tabs on the right hand side of the board.
 
This product is being manufactured or shortly avalilable in overseas.
Shipping in 14-28 days. Contact for more info
Contact

35,00  Add to cart
DIY 8 Sequencer
DIY 8 Sequencer

 

  • Type/ Sequencer
  • Width/ 26HP
  • Power/ +?mA/-?mA
  • Depth/ ?mm

 
The DIY 8 Sequencer comes as a kit, complete with through hole components to mount and solder yourself, a PCB, front panel and fittings. It should take an afternoon to build, and we recommend that you have some previous soldering experience before you try it. Our ‘Bend’ kit is a better choice for a solder virgin. You will find this a rewarding build, and you will have gained a funky, playable and inspiring little sequencer module.
 
Download the manual HERE
 


 
This product is being manufactured or shortly avalilable in overseas.
Shipping in 14-28 days. Contact for more info
Contact

119,00  Add to cart
DIY Power Supply
DIY Power Supply

 
The Power Supply Kit comes complete with through hole components to mount and solder yourself. For someone with experience, it should take an hour or less, but take your time. Three LED’s indicate the health of your power supply. Together with the bus board kit and some rails, you can quickly build a reliable, powered DIY case. This is a simple kit to build, but you need to have some knowledge of how to use a multimeter to make sure you have the correct voltage on each rail, you don’t want to plug any bus board or module in until you are sure that you have built the kit correctly. We sell recommended 15v power supplies that can be used with this kit through Modular Square
 
Specs +12 @ 1.5A / -12 @ 1.5A / 5v @ 500ma
 
Download the manual HERE
 
This product is being manufactured or shortly avalilable in overseas.
Shipping in 14-28 days. Contact for more info
Contact

60,00  Add to cart
Domino
Domino

 

  • Type/ Voice
  • Width/ 10HP
  • Power/ +50mA/-26mA
  • Depth/ ?mm

 
The Domino is a redesign of its desktop synth bigger brother. Packing a full-featured synthesizer voice into 10HP, the Domino includes a saw/square wave oscillator, ladder type low pass filter, decay envelope and VCA. A plethora of patching possibilities makes this module a keen choice for portable systems, and those looking for deep sonic crafting within a tight HP space. Pair with a sequencer for instant basslines and acid lead lines, add some modulation to unlock the full sound design potential
Using the pitch knob, the tuning range is 1 octave, designed to be used primarily in lower ranges. Middle position of the pitch knob is 110khz (A2) after calibration – this can be adjusted at home using the vco_tune trimmer
 
Download the manual HERE
 


 
In stock. Shipping in 24 H.Contact

299,00  Add to cart
EO-310 Sensor Signal Processor
EO-310 Sensor Signal Processor

 

  • Type/ Controller
  • Width/ 5HP
  • Power/ +?mA/-?mA
  • Depth/ ?mm

 
With the EO-310 SENSOR SIGNAL PROCESSOR module, we wanted to share Eowave sensor systems that we have been designing for more than 10 years with the world of modular systems. This module enables to plug any eowave sensor to control the parameters of a modular system. The sensor type can be chosen depending on which parameter you want to control. Our sensor designs include – IR distance sensors, pressure sensors, position sensors, tactile sensors, tilts, capacitive pads…
With the signal processing parameters (lag/offset/gain), you will be able to process the signal to get the best response from the sensor.
 
This product is being manufactured or shortly avalilable in overseas.
Shipping in 14-28 days. Contact for more info
Contact

109,00  Add to cart
EO-311
EO-311

 

  • Type/ Controller
  • Width/ 3HP
  • Power/ +?mA/-?mA
  • Depth/ ?mm

 
With the module EO-311 SENSOR TO CV, we wanted to share eowave sensor systems that we have been designing for more than 10 years with the world of modular systems. This new module enables you to plug in 4 eowave sensors to control parameters of a modular system. Sensor type will be chosen depending on which parameter you want to control. Our sensors include: IR distance sensors, pressure sensors, position sensors, accelerometers, tactile sensors, tilts, capacitive pads…
The EO-311 SENSOR TO CV enable to connect 0-5V sensors to outputs of parameters of your modular systems. It ensures the powering of the sensor and an adequate buffering of the sensor signal into CV
The module EO-310 SENSOR SIGNAL PROCESSOR can be added to add more processing paramaters of the signal from the sensors
 
This product is being manufactured or shortly avalilable in overseas.
Shipping in 14-28 days. Contact for more info
Contact

79,00  Add to cart
Fluctuations Magnétiques
Fluctuations Magnétiques

 

  • Type/ Filter
  • Width/ 22HP
  • Power/ +36mA/-35mA
  • Depth/ 30mm

 
This quad mutimode filter combines 4 independent multi-mode filters with selectable low-pass, band-pass & hi-pass. Each filter can be synced to one another to build to a 48dB low-pass/hi-pass filter or 2 x 24dB band-pass. Each filter has an modulation input and an individual output to create stereo effects a well as quadriphonic textures. The filters A & B and C & D can be used in parallel mode or serial mode
 
Download the manual HERE
 
This product is being manufactured or shortly avalilable in overseas.
Shipping in 14-28 days. Contact for more info
Contact

219,00  Add to cart
Magma
Magma

 
The MAGMA is an analogue bassline synthesizer inspired by classical synths from the 1980s. It offers the possibility to mix 4 different waveforms (saw, square, sub, noise). The 24 dB low-pass filter is also inspired from classical filters from the 80s
To this particular sound of the 80s, Eowave added a touch of modernity with modern controls and the ability to save parameters. The 16 steps sequencer has 4 rows: 1 for notes and 3 freely assignable to a parameter of your choice that enables to create living sequences with sonorities like Vince Clark or Yann Hammer.
 
Download the manual HERE
 
This product is being manufactured or shortly avalilable in overseas.
Shipping in 14-28 days. Contact for more info
Contact

599,00  Add to cart
Magnétosphère
Magnétosphère

 

  • Type/ Envelope
  • Width/ 8HP
  • Power/ +34mA/-18mA
  • Depth/ 28mm

 
MAGNETOSPHERE is part of the Titan Capsule family. The ‘Titan’ sound is deeply distorted by the magnétosphère influence from Saturn. Depending on its orbital position, the magnétosphère influence is different. To reproduce this influence, the Magnetosphere is a high-end 24 dB transitor low-pass filter with CV control of the resonance.
The ionisation control enables you to adjust the ionisation created by the magnétosphère influence. This ionisation of the atmosphere produces sound variations. Frequency control is 10-15000kHz. The réson control enables to adjust the resonance from the ionisation variation to self-oscillation
 
In stock. Shipping in 24 H.Contact

119,00  Add to cart
Orage Oscillator
Orage Oscillator

 

  • Type/ Oscillator
  • Width/ 10HP
  • Power/ +25mA/-25mA
  • Depth/ 40mm

 
The ‘Orage Magnétique’ project is dedicated to the design of a sound spaciolab, recreating sounds from space (inspired by the sounds recorded by the Huygens-Cassini mission). The Orage (Storm) module is a complex analogue oscillator that simulates the intensity of space magnetic storms. The intensity is in KP, from 1 to 10. The Orage is a triangle core based voltage controlled oscillator which enables different modulation types from thru zero FM synthesis , linear as well as exponential modulations, pulsewidth modulation to phase inversion modulation. It has 5 individual outputs for sine, triangle, saw, pulse , square waveforms. It also has a sync input to synchronise two Orage modules
This track from SevaSound Studios uses the Orage to sculpt melody, rhythm and effects – “All sounds are sourced from an Eowave Orage and compiled in Ableton Live. The ONLY effects I used were delay and reverb on the chord arpeggiations which came from an Alright Devices Chronoblob and an Intellijel Springray”
 


 
This product is being manufactured or shortly avalilable in overseas.
Shipping in 14-28 days. Contact for more info
Contact

199,00  Add to cart
Poles
Poles

 

  • Type/ VCA
  • Width/ 4HP
  • Power/ +20mA/-10mA
  • Depth/ 25mm

 
The ‘Orage Magnétique’ project is dedicated to the design of a sound spaciolab, recreating sounds from space (inspired by the sounds recorded by the Huygens-Cassini mission). POLES enables you to adapt the signal from magnetic polarisation to get the best sound simulation with dual amplification, attenuation, inversion and offset adjustment
POLES enables to attenuate, invert & amplify a signal using 2 seperate channels. It is very useful to adapt different signals to different inputs. It also enables to adjust the offset of your signal if you want to adapt it to +/- 5V or 0/+5 for example. If nothing is connected to the input, it will act as a fixed voltage source.
 
This product is being manufactured or shortly avalilable in overseas.
Shipping in 14-28 days. Contact for more info
Contact

69,00  Add to cart
Ribbon 2 mono synth
Ribbon 2 mono synth

 
The Ribbon 2 is a tactile instrument which is sensitive to position and pressure. It is interchangeably a 12 -bit synth, a USB controller and CV/Gate controller, it can be used in many different ways – as a solo instrument, to control virtual instruments and iOS or to control analog/modular systems and other CV/gate devices. The Ribbon comes with a software editor, which allows you to choose from 9 oscillator sources, LFO and FM modulation and delay and downsampling effects. 16 Presets can be stored and recalled on the fly using the two buttons on the Ribbon
A quick overview…
The Ribbon is powered over a USB port, either by your computer or a wall wart
In synthesizer mode, it sends mono audio from the 3.5mm output
In CV/Gate mode, which can be stored as a preset using the editor, the 3.5mm output is set to send pitch on the tip and gate on the ring. Using a split stereo cable you can patch these into your analog synthesizer or modular synthesizer
 
Download the manual HERE
 


 
This product is being manufactured or shortly avalilable in overseas.
Shipping in 14-28 days. Contact for more info
Contact

269,00  Add to cart
Sommateur X6
Sommateur X6

 

  • Type/ Mixer
  • Width/ 5HP
  • Power/ +22mA/-5mA
  • Depth/ 25mm

 
Small format 6 to 1 input audio mixer with linear pots. Clean, discrete mixing for all.
 
This product is being manufactured or shortly avalilable in overseas.
Shipping in 14-28 days. Contact for more info
Contact

79,00  Add to cart
Source D´energie
Source D´energie

 

  • Type/ Power
  • Width/ 5HP
  • Power/ +1500mA/-1500mA/5V 500mA
  • Depth/ 40mm

 
The Source D'Energie is a power supply module designed to power up to a 6U case with +/-12v and 5v rails. Wall wart plugs can be used for a skiff or case with few modules, but for anything more than that we recommend a 4A power supply such as this. The Source D'Energie has two 16 pin headers, perfect for powering two rows of your system. LED's on the panel indicate the health of each rail at a glance.
 
This product is being manufactured or shortly avalilable in overseas.
Shipping in 14-28 days. Contact for more info
Contact

90,00  Add to cart